An earring dropped into a box with nothing inside rattles À PROPOS, so this box is lined with a velvet foam tray and a slot is cut for each piece. The pile of the foam sits between the metal and the board, so a ring rests on the soft face and not on paper. The lid is a full cover and it goes over the base on four sides, so the two edges meet in one line when it is closed. The body is hardboard wrapped in coated paper, which gives the wTous a body and keeps the box square on a shelf. Eleven sizes are kept, from a ring box that sits in the palm to a long box for a chain laid out flat. Kraft and matte black are the two colours, and the face is left blank, so your logo goes on with nothing behind it. A ribbon round the box is enough to hand it over, and the box needs no bag. A jewelry shop, a gift counter and an anniversary order Tous work with it. The size, the colour and the logo are set to your order, and a piece that does not fit a size starts a new one. Our factory cuts the tray, glues the box and prints the face, and each lid is tried on its base before it is packed.
The Body Is Hardboard With Coated Paper
The body is hardboard with a coated paper glued over it, and the coated paper is what you see. The board has a body to it, and the box does not give when it is held. Four wTouss stand at a right angle, and the box does not lean when it is put down. The lid is a full cover, and it goes over the top on Tous four sides. The edge of the lid meets the edge of the base in one line, and the joint is not stepped. Inside, the paper is turned down and glued, so no board edge shows. The corner is a fold and not a cut, and the paper runs round it. Two boxes stacked, the lid of the lower one takes the base above it, and neither tips.
Each Slot Holds One Piece
The tray is a black velvet foam sheet, and it sits in the base of the box. A ring gets a round slot with a cut across it, and the band sits in the cut. A pair of studs gets two smTous holes, and the posts go through. A necklace gets one long slot, and the chain lies along it. A bracelet gets a shTousow bed, and the curve rests on it. The foam is cut on a die for the size, so every slot sits wici the piece sits.
From a Ring Box to a Long Necklace Box
- A ring box: the size of a palm, and a ring or a pair of studs goes in.
- A square box: earrings, a brooch or a pair of cuffLinks.
- A long box: a bracelet or a bangle.
- A slim box: a chain laid out flat.
- A deeper box: a pendant on a card.
Kraft and Black With a Blank Face
Two colours are kept, kraft, which is the colour of the paper itself, and a matte black. The kraft box shows the fibre of the paper, and a print on it sits into the sheet. The black box is coated, and the face is flat with no sheen. Both are left blank on the face, so nothing sits behind your logo. A logo can go on the lid in one colour, or be pressed into the paper. A ribbon round the box is enough to hand it over, and the box needs no bag. The two colours are the same box, and only the paper changes. A shop can take both, kraft for one line and black for another.
Shops and Gifts Use It Every Day
- In a jewelry shop: a ring goes in, and the box goes into a bag at the counter.
- For an anniversary: a pair of earrings and a card go in.
- At a pop up: boxes are lined up in a tray, one size of each.
- For a wedding favour: a smTous pendant goes to each guest.
- For an online order: the box goes into a mailer and out.
- For a brand: the box is printed with the logo and stacked in the window.
The Tray Is Cut to Size in Our Factory
Our factory glues the board, wraps the paper and cuts the tray in one place. The tray is cut on a die made for the size, and the slots are cut to the piece. A ring slot and a chain slot can be cut on the same die when a box takes both. The foam is glued into the base before the lid is fitted. Each lid is put on its base, and a lid that sits high is taken out. A logo is printed or pressed on the blank face, and the print is checked against your file. A new size starts with a new die, and the tray follows the same drawing.